Waste solar panels contain several valuable recyclable materials, including glass, aluminum, silicon, copper, plastics and polymers, silver and other trace metals. Each material comes from a different part of the panel and requires an appropriate separation method for recovery.
Glass is the largest material fraction, typically accounting for around 75% of a panel's total weight. Aluminum frames, silicon cells, copper conductors and polymer layers make up most of the remaining material, while silver represents a much smaller but economically valuable fraction.
Solar panel material composition
This article focuses on mainstream crystalline silicon (c-Si) solar panels. Thin-film modules are not covered because their material composition and recycling processes differ.
A typical solar panel contains several material fractions with different recycling values. The main recoverable materials include glass, aluminum, silicon, copper, plastics and silver.
Glass is the main protective layer on the front of a solar panel. It protects the solar cells from external damage and environmental exposure. Accounting for approximately 75% of the panel's weight, it represents the largest recoverable material fraction.
Because of its high volume, glass recovery is an important part of solar panel recycling. Recovered glass can be processed into glass fragments or granules and supplied to downstream glass recyclers for further processing.
Aluminum is mainly used in the frame surrounding the solar panel. It provides structural support and protects the module edges.
The aluminum frame is relatively easy to recover because it can be removed separately before the main crushing process. As a recyclable metal, aluminum can be remelted and reused in various manufacturing applications.
Silicon is the semiconductor material used in crystalline silicon solar cells. It is located inside the laminated cell layer and is usually bonded to other materials by the encapsulant.
After the panel is dismantled and processed, the silicon cells are broken down into fine particles. The resulting output is generally a mixed silicon powder containing fine particles of other materials, rather than high-purity silicon wafers.
This silicon-rich fraction can be further processed to recover valuable materials or used in suitable downstream applications. Additional purification is necessary before it can be used in high-grade silicon applications.
Waste solar panel recycling materials
Copper is mainly found in the busbars, interconnecting ribbons and electrical cables of solar panels. These components connect individual solar cells and carry the electricity generated by the module.
Copper has good recycling value and can be recovered as a copper-rich fraction or copper powder after the panel materials are dismantled and separated. Further refining may be needed to meet the requirements of downstream metal users.
The main polymer materials in crystalline silicon solar panels include EVA encapsulant, backsheet materials, junction box plastics and cable insulation.
These materials are bonded to other components or integrated into the module structure, making them more difficult to recover separately. Mechanical processing can break them into smaller particles and concentrate them into a plastic-rich powder or mixed plastic fraction.
The further recycling and use of these materials depend on their composition, contamination level and the requirements of downstream processors.
Silver is mainly used in the fine conductive grid lines printed on solar cells. Although its proportion in a solar panel is very small, it has considerable material value. Other trace metals, such as tin and lead, may also be present in electrical connections and soldering materials.
Silver-bearing particles can be released during mechanical processing, but they generally remain mixed with the fine silicon-rich fraction. Recovering silver as a separate high-purity product requires additional metal concentration and refining processes.
Material recovery involves several connected stages, from component dismantling to fine particle separation. Each stage uses specific equipment to separate different material fractions and prepare them for further recycling.
The process described below focuses on the mechanical recycling of single-glass crystalline silicon solar panels. Double-glass modules require a different treatment route. DOING ECO provides a tunnel furnace pyrolysis and sorting solution for double-glass solar panels.
The first step is to remove the junction box, external cables and aluminum frame. This stage produces separately collected aluminum frames, junction boxes and cable components. Removing these parts before further processing also prevents unnecessary metal and plastic materials from entering the main crushing system.
Solar panel aluminum frame removal
After frame removal, the remaining panel enters a glass removal machine. Controlled heating softens the EVA encapsulant, allowing the front glass to be separated from the cell laminate.
The recovered glass is collected as a separate material fraction, while the remaining laminate proceeds to the next stage. Effective glass removal reduces the amount of glass entering the crushing system and helps improve the quality of subsequent material separation.
The remaining panel laminate contains silicon cells, copper conductors and polymer materials. These components need to be broken down so that the different materials can be released from one another.
A cutting machine first divides the laminate into smaller strips. A double-shaft shredder then performs coarse size reduction, followed by a blade crusher and a blade-disc mill for further crushing and grinding. This multi-stage size-reduction process helps liberate silicon-containing particles, copper and plastics for subsequent separation.
Solar panel crushing and sorting machine
After crushing and milling, the mixture contains particles of different sizes, densities and electrical properties. A three-layer vibrating screen first classifies the material by particle size.
An air separator then uses differences in particle density and aerodynamic behavior to separate lighter and heavier fractions. An electrostatic separator further separates conductive metal-bearing particles from non-metallic materials based on their electrical properties.
Through these stages, the recycling line separates and collects different output fractions, including mixed silicon powder, copper powder and plastic. A pulse dust collection system is also used to control dust generated during processing.
The separated output streams include aluminum frames, glass, mixed silicon powder, copper-rich material and plastic. These materials can be collected separately and sent to suitable downstream recycling or refining processes. Fine metal-bearing fractions may require additional treatment to recover valuable metals such as silver.
A well-designed solar panel recycling line helps integrate these processes into an efficient material recovery system. Contact DOING ECO with your solar panel type and expected processing capacity to discuss a suitable solar panel recycling solution.
Yes. The proportions of glass, silicon, copper and other metals can vary depending on module design, manufacturer and production generation. Actual feedstock composition should be assessed before estimating material recovery.
No. Thin-film modules such as CdTe and CIGS have different semiconductor materials and structural designs. They require recycling processes suited to their specific material composition.
Not automatically. Recovered glass must meet the quality and impurity requirements of downstream buyers. Depending on its condition and purity, it may be directed to different glass recycling applications.
Please kindly leave your requirements in detail, or contact us via +86 150 3713 8562. Our professional sales manager will contact you within 24 hours. Your contact information will be protected.
Copyright © 2015-2026 DOING Holdings - Henan Doing Environmental Protection Technology Co., Ltd | Privacy Policy | All Rights Reserved